Endwall (Insert) Corner Post High Cube

(I-EWCP-HC) is part of a assembly that has material to finish the inside corners of the end wall of a standard shipping container. The corner post  inserts infill the corner’s corrugated voids preventing hidden condensation. The Metal “M” angle provides a solid corner stud for finishes like drywall. 

1. 1. Eliminates field guess work when insulating a corner post.
   2. Corner Post Insert fits the end wall corrugation.
   3. (3) part fast track application.

(I-EWCP-HC) = 12 pcs foam inserts and 4 metal “M” corner studs, each End Wall Corner section is a 3 part assembly designed to work on the inside corner end wall of a container. 

(I-EWCP-AD) = 1 End Wall Corner Inserts – interior application

InSoFast engineered system of continuous insulation perfectly suited for shipping container fabrication for the End Wall inside Corner Inserts

• Simple to install
  • Why work so hard?
  • Adaptable Attachment
  • No Special Tools Needed
• Built-in Studs*
  • Engineered Framing Studs for interior inside corners
  • Thermally isolated stud framing 
  • No energy penalty for the studs
  • Adhesive Application no holes
• Closed-cell high pressure fused EPS Insulation
  • Continuous Insulation
  • Metal framing Interlocks into the corner
    • No additional fasteners are needed
• Engineered for inside corners of a Shipping Containers
• Lives up to its name: In So Fast

Estimating and ordering is simple add together how many  interior end walls, (the “nose” of the container) your container project needs. It is simple to determine the number of boxes needed, it is 1 box per (the “nose” of the container) .  (I-EWCP-HC) = 1 End Wall Corner Inserts for each container end wall. Don’t overestimate.

• • (I-EWCP-HC) = 1 End Wall Corner Inserts – interior application

POLYURETHANE CONSTRUCTION ADHESIVE

Green Guard Certified Adhesive:

In Canada the Glue is LePage PL Premium

Estimating Adhesive Quantity

Estimating the amount of adhesive YOU will use has variables beyond our control like condition of your walls and how accurate are you with a glue gun? The example below is for one side wall of a 20′ standard height shipping container you will need approximately 3 tubes of the adhesive. That is in a perfect world. PL Premium 3x adhesive is applied in a ⅜” bead on the backside of the studs onto the ribbed surfaces.  We realize that a 3/8″ bead of glue is very subjective. It is important that there is enough adhesive to squish the dovetails on the back side of the stud when pressed to the container wall. Adhesive follows the “Goldie Locks rule, too much, too little, and just right To verify that enough adhesive is used, press the panel into place. Pull the panel back and check to see if the adhesive has spread out beyond the full width of the stud. It is normal for the panel to “float out” from the side of the container when it is accommodating irregularities in the container walls. Additional adhesive may be necessary in some areas. If you are doing it just right you can expect that 1 large 28-fl oz tube will cover 18 of our 24″ long studs or enough glue at a 3/8″ bead to cover 36 foot long bead of glue. 

Additionally you will have to estimate for glue around openings like windows and doors.

1 large 28-fl oz. / 828 mL tube = 18 (24″ studs or inserts)

• CX-LP 46 (46 studs) = 46
• 46 ÷ 18 = 2 1/2 tubes of the adhesive
• I-SWI (30) = 1 tube of the adhesive

Important Notice: Container Surface Temperature Applications

When bonding EPS and XPS foam insulation, use above 40°F (4°C) and avoid cure and surface temperatures above 90°F (32°C). Surfaces must be clean, dry and free of frost, grease, dust and other contaminants. Pre-fit all materials and protect finished surfaces. If using cartridge format, cut nozzle at a 45° angle to desired bead size and puncture inner seal. Be very careful not to allow Loctite® PL® Premium to cure on a finished surface.

Technical Data

Please read all the current Shipping, Purchasing & Returns *