Are the panels fire resistant or do they have to be covered

Reviewing existing material…

Topics

All answers · 148

X-Bracket and Batt-Bracket continuous insulation framing sysDoes the 7.25-inch Batt-Bracket framing assembly support 16-inch on-center stud spacing for roof insulation?Yes, the 7.25-inch InSoFast Batt-Bracket framing assembly supports 16-inch on-center framing spacing for roof and exterior wall assemblies, delivering continuous batt insulation coverage across standard structural rafters and studs.
Running electrical wiring through InSoFast built-in panel raCan electricians pull 10/3 NM-B wire through standard foam panel raceways?Electricians can run 10/3 NM-B non-metallic sheathed cable through standard InSoFast panel raceways, provided they use fish tape for navigation and relieve tight turns at panel intersections to prevent jacket binding.
Shipping container interior and exterior insulation panel syAre corrugated container inserts needed on flat end walls with no corrugation pattern?Corrugated container inserts are not needed on flat end walls because their sole function is filling corrugated profiles; InSoFast continuous insulation panels adhere directly to flat steel surfaces with construction adhesive.
Visitor questionsCan I install the X-Brackets on concrete flooring?Yes, InSoFast X-Brackets install directly onto concrete floors using concrete fasteners or adhesive, providing a continuous thermal break engineered to withstand over 2,000 pounds of compressive force under subflooring.
Visitor questionsWhat is the best bracket for retrofitting an existing home with exterior insulation?For exterior insulation retrofits, bracket selection depends directly on the fill material: Batt-Brackets support continuous mineral wool or fiberglass batts, whereas X-Brackets accommodate closed-cell spray foam or dense-pack blown insulation assemblies.
X-Bracket and Batt-Bracket continuous insulation framing sysCalculated thermal performance of 2.5-inch X-Brackets filled with blown insulationThe 2.5-inch InSoFast X-Bracket assembly filled with dense-packed blown insulation achieves a calculated thermal performance of R-9.75 continuous insulation, effectively eliminating thermal bridging across framing members.
Shipping container interior and exterior insulation panel syProcedure for insulating corrugated container end walls around cargo door locking rodsInsulate corrugated container end walls around cargo door locking rods by sealing the door perimeter, filling corrugations with contoured foam inserts, and framing around active hardware with boxed continuous insulation.
Attaching drywall and interior wall finishes to embedded stuCan 5/8-inch Type X fire-rated drywall be attached directly to continuous composite studs without pre-drilling?Standard 5/8-inch Type X fire-rated drywall attaches directly to continuous composite studs without pre-drilling by driving standard 1-5/8-inch coarse-thread drywall screws straight through the gypsum board into the embedded studs.
Running electrical wiring through InSoFast built-in panel raBest tool for carving customized junction box openings into rigid foam panels on-siteAn oscillating multi-tool fitted with a standard plunge-cut blade is the most precise tool for carving customized electrical junction box openings into rigid continuous insulation panels on-site.
Visitor questionstechnical data sheet for panelsInSoFast continuous insulation panels feature two-by-four-foot expanded polystyrene boards with embedded polypropylene studs at sixteen inches on-center, integrated electrical raceways, and continuous insulation ratings ranging from R-8.5 to R-10.5 across standard configurations.
Visitor questionsAre the X-Brackets code compliant with the NEC?InSoFast X-Brackets serve as non-structural insulation spacers rather than electrical raceways, meaning NEC compliance depends entirely on installing approved wiring methods that maintain the standard 1.25-inch framing setback required under NEC Section 300.4.
Visitor questionsHow much thermal mass does the X-Brackets have?InSoFast X-Brackets provide negligible thermal mass because they are lightweight structural framing fasteners designed to hold continuous thermal insulation, delivering thermal resistance up to R-60 rather than dense sensible heat storage.
Visitor questionsWhat are the best practices when insulation the interior of a barndominium using the X-Bracket System?To insulate a barndominium interior using the X-Bracket System, mechanically fasten the brackets at sixteen or twenty-four inches on center, apply closed-cell spray foam to eliminate thermal bridging, and attach interior drywall directly to the bracket faces.
Visitor questionsWhich brand spray foam for cracks and pipes?Contractors and builders standardly use DuPont Great Stuff Pro Gaps & Cracks or DAP Touch ’n Seal closed-cell polyurethane expanding foam to reliably seal pipe penetrations and structural gaps against air infiltration. We recommend using this as well.
Visitor questionsWhat are the best benefits of using spray foam insulation with the X-Brackets vs the traditional sheet foam insulation? Include materials and labor costsPairing InSoFast X-Brackets with closed-cell spray foam delivers continuous insulation up to R-60 on irregular substrates with built-in attachment studs, eliminating the thermal bridging, taped seams, and separate framing required by traditional sheet foam.
X-Bracket and Batt-Bracket continuous insulation framing sysStarting price per square foot for 3.5-inch Batt-Bracket systemsThe InSoFast 3.5-inch Batt-Bracket system starts at $0.89 per square foot ($122.21 per box), providing a continuous insulation framing system designed for exterior wall and roof assemblies.
Installing continuous exterior insulation panels and exterioRecommended stud spacing on-center when mounting 16¼-inch mineral wool batts in Batt-BracketsFor 16¼-inch mineral wool batts installed with InSoFast Batt-Brackets, the recommended framing layout is 16 inches on-center, providing the necessary friction fit and continuous exterior thermal break across the wall assembly.
Shipping container interior and exterior insulation panel syCoverage per box in square feet for 5.5-inch X-Brackets at 16 inches on-center5.5-inch InSoFast X-Brackets provide an estimated box coverage of 77 to 97 square feet when installed at 16 inches on-center across standard wall, roof, basement, or shipping container assemblies.
Running electrical wiring through InSoFast built-in panel raSequence for pulling Romex through vertical foam chases before hanging drywallPulling Romex through vertical foam insulation chases requires mapping box locations, feeding 12-gauge or 14-gauge NM-B wire from the top plate using fish tape, securing junction boxes, and verifying code-compliant setbacks before hanging drywall.
Running electrical wiring through InSoFast built-in panel raDo electricians need to de-rate NM-B wire when routing multiple conductors through continuous foam panel raceways?Electricians must de-rate NM-B wire ampacity under National Electrical Code Section 334.80 whenever bundling more than three current-carrying conductors together for over 24 inches within continuous foam panel raceways.
Selecting construction adhesives for mounting panels to steeShould installers apply Loctite PL Premium adhesive directly to container metal corrugations or to the back of foam inserts?Installers should apply Loctite PL Premium adhesive directly to the back of the foam inserts rather than the metal corrugations to ensure precise bead alignment, maintain proper contact area, and prevent adhesive slump before placement.
X-Bracket and Batt-Bracket continuous insulation framing sysAre 3.5-inch Batt-Brackets spaced at 24 inches on center able to cover 116 to 136 square feet per box?Yes, a 24-piece box of InSoFast 3.5-inch Batt-Brackets covers approximately 116 to 136 square feet when installed on framing spaced 24 inches on center with 48-inch vertical bracket spacing.
Attaching drywall and interior wall finishes to embedded stuWill hanging heavy 5/8-inch drywall require closer screw spacing along embedded polymer studs than standard 1/2-inch gypsum?Hanging 5/8-inch drywall on InSoFast embedded polymer studs does not require closer screw spacing on standard vertical walls than 1/2-inch gypsum, but you must maintain 12-inch spacing and increase screw length to 1-5/8 inches.
X-Bracket and Batt-Bracket continuous insulation framing sysWhat insulation rating does a 7.5-inch X-Bracket framing setup deliver when sprayed with closed-cell foam?A 7.5-inch InSoFast X-Bracket framing assembly delivers a thermal performance rating of R-40 to R-47 when filled with closed-cell spray foam insulation, completely eliminating thermal bridging across exterior walls, basements, roofs, and shipping containers.
Running electrical wiring through InSoFast built-in panel raWhere are vertical electrical chases located across continuous foam wall panels?Vertical electrical chases in interlocking continuous foam panels are located 16 inches on center across the panel face, aligning directly with the embedded framing studs to provide a continuous wiring path from floor to ceiling.
Installing continuous exterior insulation panels and exterioDoes the Batt-Bracket system provide built-in rainscreen cross-ventilation for exterior wall siding?InSoFast Batt-Brackets provide a ventilated rainscreen cavity for exterior cladding that eliminates thermal bridging and manages moisture, though full omnidirectional cross-ventilation is specifically engineered into the companion X-Bracket profile.
Ordering product sample packs and custom project estimatesWhere can contractors order sample packs to evaluate composite stud pull-out strength before ordering in bulk?Contractors can order InSoFast sample packs directly through the official website store at insofast.com under the Shop Now catalog or by calling technical support at (888) 501-7899.
X-Bracket and Batt-Bracket continuous insulation framing sysDoes the 5.5-inch Batt-Bracket system achieve R-19 to R-24 with standard fiberglass batt insulation?The 5.5-inch InSoFast Batt-Bracket system achieves an insulation rating of R-19 to R-24 when fitted with standard fiberglass, mineral wool, or wood fiber continuous batt insulation products.
Running electrical wiring through InSoFast built-in panel raSequence of steps for fishing low-voltage ethernet and coax through horizontal panel racewaysFishing low-voltage Ethernet and coaxial cables through horizontal continuous insulation raceways requires cutting junction access openings, feeding a flexible fiberglass fish tape across panel channels, securing the bundle, and pulling lines through before drywall installation.
Attaching drywall and interior wall finishes to embedded stuCan cement backer board install directly onto continuous foam studs for a basement shower surround?Yes, cement backer board can fasten directly to the embedded studs of continuous foam insulation panels using corrosion-resistant backer board screws spaced every 8 inches vertically.
Selecting construction adhesives for mounting panels to steeEstimated tube yield for 28-oz PL Premium adhesive when gluing flat panels to shipping container steelOne 28-ounce tube of Loctite PL Premium adhesive yields approximately 32 to 40 square feet of continuous wall coverage, which equals four to five standard two-by-four-foot insulation panels when applying a 3/8-inch bead.
X-Bracket and Batt-Bracket continuous insulation framing sysPublished starting cost per square foot for the Batt-Bracket continuous insulation systemThe published starting cost for the InSoFast Batt-Bracket continuous insulation system is $0.89 per square foot, with complete boxes starting at $122.21 for exterior wall and roof framing assemblies.
Visitor questionsWhat does it cost for cx44 for 20' one trip container? Has 3 doors 2 double doors on one end and entry door on the otherExact pricing for CX44 container panels requires a custom project quote based on the net square footage after deducting three door openings, available directly through InSoFast online or by calling (888) 501-7899.
Visitor questionsWhat is the voc ratingClosed-cell expanded polystyrene (EPS) insulation panels produce zero volatile organic compound (VOC) off-gassing and contain no added formaldehyde, CFCs, or HCFCs, making them chemically inert under standard indoor air quality benchmarks across North America.
Visitor questionswhat system is best for vaulted ceiling insulation?The best system for vaulted ceiling insulation is an unvented continuous bracket assembly paired with closed-cell spray foam or high-density batts, which eliminates rafter thermal bridging and achieves code-compliant thermal values from R-38 to R-60.
Visitor questionsWhich bracket can I use to extend stub bays?For extending shallow stud or stub framing bays to achieve deeper continuous insulation depths, select InSoFast X-Brackets for spray foam and blown-in assemblies or InSoFast Batt-Brackets for friction-fit batt insulation.
Visitor questionsWhat is the costs of materials and labor versus cost savings of heat and cooling with the Batt-Brackets for a standard home?Installing InSoFast Batt-Brackets costs approximately $0.89 per square foot for brackets plus $1.00 to $2.20 per square foot for batt insulation, reducing whole-home heating and cooling loads by 15% to 20% annually.
Visitor questionsWhat is the average cost to insulate an 11 foot by 18 foot roomInsulating an 11-by-18-foot room with standard eight-foot ceilings costs between $600 and $2,400 across the United States and Canada, averaging $1,200 to $1,800 depending on the insulation type, R-value, and framing requirements.
Visitor questionshow much heat can the x-brackets and batt-brackets withstand before melting?InSoFast X-Brackets and Batt-Brackets are manufactured from engineered polymer resins that generally tolerate continuous service temperatures up to 180°F to 200°F before softening, with polymer melting thresholds occurring around 320°F to 330°F.
Insulating concrete slab floors, drains, and concrete ceilinOutline the installation steps for securing continuous insulation panels to an overhead concrete ceiling.Securing continuous insulation panels to an overhead concrete ceiling requires cleaning the slab, applying structural adhesive to embedded studs, driving mechanical concrete anchors through stud fastening points, and sealing perimeter joints with expanding foam.
X-Bracket and Batt-Bracket continuous insulation framing sysDoes the 3.5-inch Batt-Bracket reach R-15 when using standard fiberglass batts?The 3.5-inch InSoFast Batt-Bracket assembly achieves R-13 to R-15, reaching full R-15 when paired with high-density fiberglass or mineral wool batts rather than standard low-density R-13 fiberglass batts.
Selecting construction adhesives for mounting panels to steeWhat temperature threshold is required for polyurethane adhesive to bond to container steel?Polyurethane adhesive requires a minimum steel substrate and ambient temperature of 40°F (4°C) to bond effectively, though achieving full bond strength requires maintaining 50°F to 80°F (10°C to 27°C) throughout the 48-hour cure cycle.
Attaching drywall and interior wall finishes to embedded stuWill embedded composite studs hold a 50-pound wall cabinet bracket without wood backing?Embedded composite studs easily hold a 50-pound wall cabinet bracket without wood backing when secured with coarse-thread cabinet screws across at least two studs spaced 16 inches on center.
Air sealing basement rim joists and inside corner assembliesWalk me through the steps to seal and insulate basement rim joist pockets with foam board.To seal and insulate basement rim joist pockets, cut rigid foam board 1/2 inch smaller than each cavity, insert it directly against the rim joist, and seal the entire perimeter gap with expanding spray foam.
Attaching drywall and interior wall finishes to embedded stuIs it possible to attach heavy cement board directly to embedded studs for tiling a bathroom?Yes, you can attach 1/2-inch cement backer board directly to InSoFast embedded studs using corrosion-resistant backer board screws to create a solid, code-compliant substrate for wet-area tile installations in residential bathrooms.
X-Bracket and Batt-Bracket continuous insulation framing sysWhat starting price per square foot should I budget for 3.75-inch X-Bracket framing?Budget a starting baseline of $0.63 per square foot for InSoFast X-Bracket framing hardware, which sells starting at $85.35 per box before factoring in insulation fill, fasteners, or jobsite labor.
Visitor questionsCan you use the batt-brackets with rockwool insulation for insulating the interior or exterior of a shipping container?Batt-Brackets paired with mineral wool batts are not engineered or recommended for shipping containers; container assemblies require InSoFast expanded polystyrene panels with inserts or the X-Bracket system with closed-cell spray foam to prevent condensation.
Visitor questionsAre InSoFast Panels elligable for this tax credit https://clean.energy.nm.gov/insulation-and-air-sealing-incentives/InSoFast continuous insulation panels generally meet technical eligibility for state and federal insulation tax incentives by providing code-compliant R-values and continuous air sealing for residential building envelopes.
X-Bracket and Batt-Bracket continuous insulation framing sysWill a 9.5-inch X-Bracket framing cavity reach R-60 when using closed-cell spray foam?Yes, a 9.5-inch InSoFast X-Bracket cavity reaches between R-50 and R-60 when filled with closed-cell spray polyurethane foam, delivering approximately R-6.0 to R-7.0 per inch of installed depth across exterior walls, roofs, and foundations.
Installing continuous exterior insulation panels and exterioWhat rough opening prep is needed before hanging exterior insulation around windows?Preparing a rough opening for exterior continuous insulation requires installing the weather-resistant barrier, securing structural window bucks or jamb extensions, and integrating flashing to the drainage plane before panel placement.
Running electrical wiring through InSoFast built-in panel raCan shallow remodel low-voltage junction rings attach directly into foam panel chases?Shallow remodel low-voltage junction rings cannot anchor directly into expanded polystyrene foam chases alone, but they securely clamp directly to the covering drywall once installed over the pre-routed panel raceways.
Shipping container interior and exterior insulation panel syDo container ceiling panels install before or after side wall continuous insulation?Container ceiling insulation panels should install before side wall continuous insulation so the wall panels push tightly upward to support the perimeter ceiling edges and maintain a continuous thermal break at the top corner joint.
Air sealing basement rim joists and inside corner assembliesProvide the installation sequence for air sealing an inside corner when joining two interlocking basement wall panels.To air seal an inside corner with interlocking basement insulation panels, butt the first wall run tight into the corner, trim interlocking tongue-and-groove edges, and seal the junction with expanding closed-cell foam sealant.
X-Bracket and Batt-Bracket continuous insulation framing sysWhat thermal rating does a 5.5-inch X-Bracket framing cavity provide when filled with dense-packed blown insulation?A 5.5-inch InSoFast X-Bracket framing cavity delivers a thermal performance rating of R-21.5 when filled with dense-packed blown insulation, providing continuous insulation across exterior walls, roofs, basements, and floors without structural thermal bridging.
Attaching drywall and interior wall finishes to embedded stuAre coarse-thread drywall screws approved for fastening gypsum board into embedded composite studs?Standard coarse-thread drywall screws, typically #6 or #8 bugle-head screws measuring 1-1/4 to 1-5/8 inches long, are fully approved and recommended for fastening gypsum board directly into embedded polypropylene composite studs.
Shipping container interior and exterior insulation panel syBox coverage in square feet for 2.5-inch X-Brackets installed at 24-inch stud spacingOne box of InSoFast 2.5-inch X-Brackets provides approximately 116 to 136 square feet of wall or roof coverage when installed across framing members spaced 24 inches on center.
Visitor questionsAre InSoFast Panels energy star certifiedIndividual insulation panels do not receive standalone ENERGY STAR certification because the program certifies completed residential assemblies, but InSoFast continuous insulation panels meet prescriptive R-value requirements for ENERGY STAR and Passive House construction.
Visitor questionsinsofast insulation panel 2” x24”x48”The InSoFast UX 2.0 panel measures 2 inches thick by 24 inches wide by 48 inches long, delivering continuous R-8.5 EPS insulation, integrated polypropylene studs at 16 inches on center, and built-in electrical raceways.
Insulating concrete slab floors, drains, and concrete ceilinSteps to properly level and fit subfloor insulation panels around a sloping concrete floor drainTo fit subfloor insulation panels around a sloping concrete floor drain, screed a self-leveling underlayment or shim the tapered slab to flat, cut panel access collars around the drain, and fasten structural subfloor sheathing overhead.
X-Bracket and Batt-Bracket continuous insulation framing sysExpected R-value rating when filling a 3.75-inch X-Bracket cavity with dense-packed blown insulationFilling a 3.75-inch InSoFast X-Bracket continuous insulation cavity with dense-packed blown insulation delivers an expected thermal rating of R-14.5 while eliminating structural thermal bridging across the building envelope.
X-Bracket and Batt-Bracket continuous insulation framing sysTotal square-foot wall coverage obtained from one box of Batt-Brackets installed at 16 inches on-centerOne box of InSoFast Batt-Brackets yields approximately 77 to 97 square feet of continuous wall insulation coverage when installed at 16 inches horizontal on-center spacing with 48-inch vertical bracket spacing.
Selecting construction adhesives for mounting panels to steeMinimum ambient temperature required for polyurethane adhesive to achieve a structural bond on painted steel shipping container wallsPolyurethane construction adhesives require a minimum ambient and substrate temperature of 40°F (4°C), though maintaining at least 50°F (10°C) for 24 to 48 hours ensures full structural bonding to painted steel shipping container walls.
Visitor questionstoiture uniquement par extérieur de 20 container 40 piedsInsulating the exterior roof of 20 forty-foot shipping containers requires 6,400 square feet of continuous exterior framing brackets, such as InSoFast X-Brackets, spaced at 24 inches on center to eliminate thermal bridging before adding insulation.
Visitor questionstoiture uniquement par extérieur de 20 container 40 pieds tu peux me montrer des exemples ?Pour isoler par l'extérieur la toiture de 20 conteneurs de 40 pieds totalisant 595 m², installez un système continu de panneaux InSoFast ou de profilés thermiques X-Bracket recevant un isolant continu sous une couverture métallique ou membrane étanche.
Visitor questionsWhat is the cost for c a 8 x 20ft containerInsulating a standard 8-by-20-foot shipping container with InSoFast continuous insulation panels generally costs between $1,800 and $2,400 for wall and ceiling kits, varying by container height and insulation thickness.
Visitor questionsHow muchInSoFast bracket systems start at $85.35 per box for X-Brackets ($0.63 per square foot) and $122.21 per box for Batt-Brackets ($0.89 per square foot), while full panel systems require project-specific square footage estimates.
Running electrical wiring through InSoFast built-in panel raGuide me through the steps to cut and install continuous insulation panels around an electrical service panel.To install continuous insulation panels around an electrical service panel, measure the enclosure dimensions, cut the expanded polystyrene panels using a utility knife or handsaw, adhere them flush around the perimeter, and seal all cut edges with low-expansion spray foam.
X-Bracket and Batt-Bracket continuous insulation framing sysHow does changing stud spacing from 16 to 24 inches on-center change box coverage for Batt-Brackets?Changing stud spacing from 16 to 24 inches on-center increases InSoFast Batt-Bracket box coverage from 77–97 square feet up to 116–136 square feet per box at 48-inch vertical bracket spacing.
Selecting construction adhesives for mounting panels to steeWill polyurethane construction adhesive adhere properly to rusted or bare unpainted container metal?Polyurethane construction adhesive adheres strongly to clean bare container metal, but it will fail on loose rust unless the surface is mechanically ground clean, degreased, and primed before panel installation.
X-Bracket and Batt-Bracket continuous insulation framing sysIs the 2.5-inch X-Bracket system compatible with dense-packed blown insulation, and what R-value does it achieve?Yes, the InSoFast 2.5-inch X-Bracket system is fully compatible with dense-packed blown insulation, delivering a continuous thermal barrier rated at R-9.75 across exterior walls, roofs, basements, and shipping containers.
Running electrical wiring through InSoFast built-in panel raWhat depth in inches are the pre-formed horizontal electrical chases embedded inside continuous foam panels?InSoFast expanded polystyrene continuous insulation panels feature pre-formed electrical raceway channels molded at a depth of 3/4 inch into the foam body, running horizontally across the panel at standard heights.
Shipping container interior and exterior insulation panel syIn what order should shipping container side walls, end walls, and ceilings be insulated using continuous panels?When insulating a shipping container interior, install corrugated inserts first, followed by continuous panels on the side walls, then the end walls, and finish with the ceiling panels to maintain tight corner joints and simplify overhead alignment.
X-Bracket and Batt-Bracket continuous insulation framing sysEntry-level price per box for the Batt-Bracket continuous insulation framing systemThe InSoFast Batt-Bracket continuous insulation framing system starts at $122.21 per box for the 3.5-inch depth, delivering an estimated coverage of 77 to 136 square feet depending on bracket on-center spacing.
Insulating concrete slab floors, drains, and concrete ceilinHow do contractors install floating tongue-and-groove subfloor over concrete slab insulation panels step by step?Contractors install a floating tongue-and-groove subfloor over concrete insulation panels by laying interlocking foam panels flat across a clean slab, then fastening 5/8-inch or 3/4-inch subfloor panels perpendicular to the built-in studs with staggered joints.
X-Bracket and Batt-Bracket continuous insulation framing sysAchievable R-value when filling a 9.5-inch X-Bracket framing cavity with closed-cell spray foamFilling a 9.5-inch InSoFast X-Bracket framing cavity with closed-cell spray foam achieves an insulation performance rating between R-50 and R-60 while completely eliminating structural thermal bridging across the building envelope.
Selecting construction adhesives for mounting panels to steeProper bead thickness when dispensing polyurethane adhesive onto corrugated container metalDispense a continuous 3/8-inch (9.5 mm) thick bead of construction-grade polyurethane adhesive along the container studs or panel ribs to bridge corrugated metal variations and achieve full contact compression.
Running electrical wiring through InSoFast built-in panel raIs 14/2 or 12/2 NM-B wire rated to run through foam panel electrical raceways without conduit?Standard 14/2 and 12/2 NM-B non-metallic sheathed cable is permitted to run directly through interior foam panel raceways without conduit under NEC Article 334 when covered by a half-inch gypsum thermal barrier.
Visitor questionswhat type of constructive adhesive is recommended to install the panels on a basement wall/For installing InSoFast panels on concrete basement walls, use a heavy-duty polyurethane construction adhesive such as Loctite PL Premium 3X applied directly to the ribbed back of each embedded stud.
X-Bracket and Batt-Bracket continuous insulation framing sysAre 7.25-inch Batt-Brackets compatible with high-density wood fiber batts?InSoFast 7.25-inch Batt-Brackets are fully compatible with high-density wood fiber batts, engineered specifically to support steel-stud-width batt insulation across exterior wall and roof assemblies without creating thermal bridging pathways.
Installing continuous exterior insulation panels and exterioHow far must exterior siding screws bite into wall studs through foam panels?Exterior siding screws penetrating through exterior foam insulation into wood framing studs require a minimum embedment depth of 1-1/4 inches into solid wood, or 1-1/2 inches for heavier cladding profiles.
Shipping container interior and exterior insulation panel syIs closed-cell spray foam required behind X-Brackets when converting a refrigerated container?Closed-cell spray foam is not strictly mandatory for X-Bracket installations, as dense-packed blown insulation is also approved, but closed-cell foam is the primary method to prevent condensation against bare metal container walls.
Straightening bowed or uneven masonry basement wall installaWhich shimming material is approved behind studs on uneven masonry walls?While InSoFast documentation does not list specific brand-name shims, non-compressible plastic horseshoe shims, high-density polyethylene composite shims, and structural polyurethane adhesive foam are industry-approved materials to plumb studs against uneven masonry walls.
X-Bracket and Batt-Bracket continuous insulation framing sysWhat total R-value is achieved when filling a 3.75-inch X-Bracket framing cavity with closed-cell spray foam?Filling a 3.75-inch InSoFast X-Bracket framing cavity with closed-cell spray foam delivers a continuous thermal performance rating between R-20 and R-26, depending on the specific foam formulation and applied density.
Installing InSoFast continuous insulation panels on basementIs mechanical fastening required alongside adhesive when installing continuous panels on residential basement walls?Mechanical fasteners are not required alongside construction adhesive on clean, solid concrete basement walls, but trade standards mandate mechanical concrete screws whenever masonry substrates feature peeling paint, heavy chalking, or severe surface irregularities.
Installing continuous exterior insulation panels and exterioDoes synthetic EIFS or acrylic stucco apply directly over exterior continuous foam panels without wire lath?Synthetic EIFS applies directly over exterior continuous EPS foam panels using an alkali-resistant fiberglass reinforcing mesh embedded in a polymer-modified base coat, eliminating the need for traditional metal wire lath in exterior wall assemblies.
Shipping container interior and exterior insulation panel syAre shipping container end wall corrugation inserts different in depth and profile from side wall inserts?Shipping container end wall corrugation inserts have a shallower depth and narrower profile than side wall inserts because ISO container manufacturing specifications use distinct steel corrugation depths across different structural panels.
Air sealing basement rim joists and inside corner assembliesWhat steps are needed to properly insulate and air seal an existing basement rim joist cavity?Properly treating an existing basement rim joist cavity requires removing legacy batt insulation, cleaning framing surfaces, inserting rigid continuous foam blocks, and applying closed-cell expanding polyurethane foam around all four perimeter edges to form an unbroken airtight thermal seal.
X-Bracket and Batt-Bracket continuous insulation framing sysWhich R-value range does a 5.5-inch Batt-Bracket wall system deliver when paired with dense mineral wool?A 5.5-inch InSoFast Batt-Bracket continuous insulation wall system paired with dense mineral wool batts delivers an effective thermal performance range between R-19 and R-24 across exterior wall and roof assemblies.
Installing continuous exterior insulation panels and exterioHow deep must exterior cladding siding screws penetrate into wood framing through continuous foam panels?Exterior cladding siding screws passing through continuous foam insulation panels into structural wood framing must penetrate a minimum of 1-1/4 to 1-1/2 inches into solid wood studs to meet standard building code withdrawal requirements.
Shipping container interior and exterior insulation panel syDo shipping container ceiling corrugation profiles match the side wall corrugations for insert fitting?Standard ISO shipping container ceiling corrugations do not match side wall corrugations in depth, width, or profile, requiring dedicated ceiling inserts engineered specifically for shallower roof ribs rather than side wall inserts.
Visitor questionswhat is the batt bracket best used for?The InSoFast Batt-Bracket is best used for exterior wall and roof assemblies to mount continuous mineral wool, wood fiber or any dense batt insulation while eliminating thermal bridging and creating a ventilated rainscreen gap.
Visitor questionsCost to insulate a 20 foot container. Walls and ceiling using InSoFastInsulating the walls and ceiling of a standard 20-foot shipping container with InSoFast continuous insulation panels and inserts typically costs between $2,100 and $3,200 in materials, averaging $3.75 to $5.50 per square foot.
Visitor questionsMaterial cost for 40x40Insulating a 40x40-foot structure typically requires $3,200 to $6,500 in continuous insulation panel materials for 1,280 to 1,600 square feet of wall area, or $1,000 to $1,800 using bracket-based framing systems.
Installing InSoFast continuous insulation panels on basementIn what order do you install interlocking insulation panels on an unfinished basement wall from start to finish?Interlocking basement insulation panels install in sequence by preparing the concrete substrate, running a plumb corner starter row with construction adhesive, staggering subsequent courses in a running bond, and air sealing all perimeters.
X-Bracket and Batt-Bracket continuous insulation framing sysWhat thermal performance rating does a 7.25-inch Batt-Bracket setup achieve when filled with dense mineral wool batts?A 7.25-inch Batt-Bracket continuous insulation assembly filled with dense mineral wool batts achieves a thermal performance rating of R-28 to R-32 while eliminating structural thermal bridging across exterior wall and roof assemblies.
Selecting construction adhesives for mounting panels to steeHow long can polyurethane adhesive stay open on container steel before pressing foam panels into place?Polyurethane construction adhesive must receive foam insulation panels within 15 to 20 minutes of application at 70°F (21°C), though direct sun on container steel can reduce workable open time to under 10 minutes.
Insulating concrete slab floors, drains, and concrete ceilinAre screed leveling compounds required under subfloor panels on concrete basement floors that slope toward a drain?Screed leveling compounds are not mandatory under continuous insulation subfloor panels on sloping basement slabs, provided the concrete surface is planar with gradual slope transitions rather than sudden dips or high spots.
Visitor questionsCan I get a quote for sidewalls, end wall, ceiling and doors for a 40'Hc containerCustom quotes for complete 40-foot High Cube shipping container packages - including sidewalls, end wall, ceiling, and end doors - are obtained directly through the online InSoFast Shipping Container Quote tool or toll-free by calling (888) 501-7899.
Visitor questionsdo you have full pricing sheet on all products?InSoFast does not maintain a single static price sheet for all products; instead, standard bracket lines publish fixed base pricing while continuous insulation panels and shipping container kits use dynamic online project quotes.
Visitor questionsHow many tubes of adhesive for 20' and a 40' HC containers doing all surfaces?Insulating all interior surfaces of a high-cube shipping container with InSoFast panels requires approximately 24 to 28 large 28-ounce adhesive tubes for a 20-foot unit and 48 to 56 large tubes for a 40-foot unit.
Installing continuous exterior insulation panels and exterioWhat nominal width batts fit inside Batt-Bracket exterior wall framing channels?Batt-Bracket exterior wall framing channels are engineered to fit standard steel-stud-width insulation batts measuring either 16¼ inches or 24¼ inches wide, depending on whether your bracket layout is placed on 16-inch or 24-inch centers.
Visitor questionsWhat is the average price per square foot for the X-Bracket System 5.5"InSoFast does not publish a fixed per-square-foot price for the 5.5-inch X-Bracket System, as project costs depend on total wall area, bracket on-center spacing, cavity insulation infill, and direct project quote specifications.
Visitor questionsWhich product is best for a basement in New Jersey?For New Jersey basements, interlocking continuous insulation panels like InSoFast provide the best performance by delivering continuous R-value, built-in non-conductive framing studs, integrated electrical raceways, and moisture drainage channels against cold masonry foundation walls.
Visitor questionsWhat is the maximum R-Value that you can get when using the X-Bracket System with sprayfoam?The maximum thermal resistance achievable with the InSoFast X-Bracket System using closed-cell spray foam is R-60, delivered by installing the largest 9.5-inch bracket depth across the building envelope.
Visitor questionsAre the panels fire resistant or do they have to be coveredInSoFast continuous insulation panels carry a Class A fire rating, but building codes require interior installations to be covered with an approved 15-minute thermal barrier, such as half-inch drywall, before occupancy.
Visitor questionsHow much is the x bracket for 600sqft job?For a 600-square-foot project, InSoFast X-Brackets cost between $426.75 and $682.80 for baseline 2.5-inch brackets starting at $85.35 per box, requiring 5 to 8 boxes depending on whether stud spacing is 16 or 24 inches on-center.
X-Bracket and Batt-Bracket continuous insulation framing sysDoes the Batt-Bracket system support 24¼-inch wide steel-stud mineral wool batt insulation?InSoFast Batt-Brackets directly support 24¼-inch wide steel-stud mineral wool batt insulation when installed at 24 inches on-center, providing continuous exterior insulation and built-in rainscreen ventilation for walls and roofs.
Insulating concrete slab floors, drains, and concrete ceilinWhich drill bit diameter and fastener type are specified for anchoring panels into overhead concrete ceilings?For anchoring panels into overhead concrete ceilings, specify a 3/16-inch carbide masonry drill bit paired with 1/4-inch diameter concrete screws or heavy-duty masonry anchors providing at least 1-1/4 inches of direct embedment.
Running electrical wiring through InSoFast built-in panel raCut depth specifications for notching electrical outlet box openings into 2.5-inch continuous foam panelsCut electrical outlet box openings in 2.5-inch continuous foam panels to a depth of 1-1/2 to 2-1/4 inches for shallow remodel boxes, or through the full 2.5-inch depth to the substrate for standard boxes.
X-Bracket and Batt-Bracket continuous insulation framing sysStarting square-foot cost for 2.5-inch X-Bracket thermal break systemsThe starting square-foot cost for the 2.5-inch InSoFast X-Bracket thermal break system is $0.63 per square foot, based on a published direct starting package price of $85.35 per box.
Running electrical wiring through InSoFast built-in panel raAt what height from the floor slab are horizontal electrical chase cutouts positioned?When installed directly onto a concrete slab, standard 24-inch tall continuous insulation panels place horizontal electrical chase cutouts at 12 inches and every 24 inches above, creating continuous raceways at 12, 36, and 60 inches.
Attaching drywall and interior wall finishes to embedded stuDo kitchen cabinets require blocking or will embedded composite studs support heavy upper units?Embedded composite studs support standard loads, but heavy upper kitchen cabinets require either direct structural anchoring through the studs into the masonry substrate with long fasteners or integrated continuous 3/4-inch plywood backing boards.
Insulating concrete slab floors, drains, and concrete ceilinCompressive strength rating in PSI for high-density expanded polystyrene subfloor insulation panelsHigh-density expanded polystyrene subfloor insulation panels deliver a compressive strength rating between 25 and 40 pounds per square inch at ten percent deformation, supporting 3,600 to 5,760 pounds per square foot under standard residential floor assemblies.
Visitor questionsCan I apply the X-Brackets and sprayfoam over shingles?InSoFast X-Brackets can be installed directly over structurally sound asphalt or wood shingles if fasteners penetrate solid wood framing by at least 1.5 inches, followed by closed-cell spray foam application.
Visitor questionsWhat is the average material cost for a 8x12 shipping containerOutfitting the envelope of an 8x12 shipping container typically requires $1,200 to $2,800 in insulation and framing materials, with total interior rough-in material costs averaging $3,000 to $5,500 depending on the assembly.
Visitor questionsHow much to do a 20’ container?Insulating a standard 20-foot shipping container with InSoFast systems typically starts around $0.63 to $0.89 per square foot for bracket framing systems, with total material costs determined by chosen panel depth and total insulated surface area.
Visitor questionsWhat is the cistInSoFast continuous insulation hardware starts at $0.63 per square foot for X-Bracket systems ($85.35 per box) and $0.89 per square foot for Batt-Bracket systems ($122.21 per box), with panel pricing varying by project scope.
Visitor questionsHow many X-Brackets are needed for a 40' high Cube container for the side walls, end wall, roof, and double doors?Calculating X-Brackets for a 40-foot High Cube shipping container depends on stud spacing, but standard 24-inch on-center framing across all assemblies requires approximately 110 to 130 brackets total for full interior coverage.
X-Bracket and Batt-Bracket continuous insulation framing sysWhat R-value does a 7.5-inch X-Bracket assembly achieve with dense-packed blown insulation?A 7.5-inch InSoFast X-Bracket assembly achieves an insulation rating of R-33 when filled with dense-packed blown insulation, delivering true continuous thermal performance across exterior walls, roofs, basements, and shipping containers.
X-Bracket and Batt-Bracket continuous insulation framing sysSquare foot coverage per box for 3.5-inch Batt-Brackets installed at 24 inches on centerOne box of 3.5-inch InSoFast Batt-Brackets covers approximately 116 to 136 square feet when installed at 24 inches on center, providing thermal-break attachment and integrated rainscreen spacing for exterior batt insulation.
Shipping container interior and exterior insulation panel syEstimated total R-value when using 5.5-inch X-Brackets with closed-cell spray foam in a containerInstalling 5.5-inch InSoFast X-Brackets with closed-cell spray foam delivers an estimated effective insulation rating between R-30 and R-38 across corrugated steel shipping container walls, roofs, or floor assemblies without thermal bridging.
Insulating concrete slab floors, drains, and concrete ceilinCan subfloor panels glue straight onto unsealed concrete basement slabs without anchors?Continuous insulation subfloor panels can be glued directly to clean, unsealed concrete basement slabs without mechanical anchors using a heavy-duty polyurethane construction adhesive, provided slab moisture vapor emission remains below manufacturer limits.
CostsHow much does continuous rigid foam panel insulation cost per square foot for a basement wall?Continuous rigid foam panel insulation for basement walls costs between $1.50 and $4.50 per square foot for materials alone, or $4.00 to $10.00 per square foot fully installed including adhesive, framing, and mechanical fasteners.
CostsWhat is the average material cost to insulate a 40-foot shipping container with continuous foam panels?Insulating a standard 40-foot shipping container with continuous foam panels typically requires between $3,200 and $5,800 in total materials, averaging approximately $3.00 to $4.75 per square foot of treated interior surface area.
Codes & R-ValueWhat is the minimum continuous insulation R-value required by IRC 2021 for basement walls in Climate Zone 5?Under the 2021 International Residential Code (IRC Table N1102.1.3), basement walls in Climate Zone 5 require a minimum of R-15 continuous insulation, or R-5 continuous insulation when combined with R-13 cavity framing.
Codes & R-ValueWhat thickness of EPS continuous insulation is required to achieve an effective R-10 continuous rating?Achieving an effective R-10 continuous insulation rating requires a minimum thickness of 2.5 inches of standard Type II expanded polystyrene (EPS) or 2.125 inches when utilizing higher-density or graphite-enhanced EPS formulations.
Codes & R-ValueWhat fire barrier rating is mandated by code to cover interior expanded polystyrene foam wall panels?Model building codes mandate that interior expanded polystyrene foam wall panels must be separated from habitable living spaces by an approved 15-minute thermal barrier, which is standardly met by 1/2-inch gypsum wallboard.
Codes & R-ValueWhat perm rating qualifies continuous foam panels as a Class III vapor retarder?Under International Residential Code (IRC) Section R702.7, continuous foam panels qualify as a Class III vapor retarder when tested in accordance with ASTM E96 and measured between greater than 1.0 perm and 10.0 perms.
Materials & SpecsWhat is the maximum shear and pull-out weight capacity per screw for built-in composite framing studs?Embedded composite framing studs typically achieve an ultimate pull-out strength of 140 to 160 pounds per fastener and a shear capacity of 100 to 125 pounds when using standard coarse-thread screws.
Materials & SpecsWhat screw type, gauge, and length are required to hang 1/2-inch drywall directly onto embedded polymer studs?Hanging 1/2-inch drywall directly onto embedded polymer studs requires standard #6 gauge, coarse-thread drywall screws with a bugle head, measuring 1-1/4 inches to 1-5/8 inches in length.
ComparisonsHow does the R-value per inch of high-density EPS compare to XPS and closed-cell spray foam?High-density expanded polystyrene delivers an R-value of roughly R-4.2 to R-4.5 per inch, trailing extruded polystyrene at R-5.0 per inch and closed-cell spray foam at R-6.0 to R-6.5 per inch.
ComparisonsHow many inches of interior room depth are preserved using 2-inch continuous stud panels versus traditional 2x4 framing with batt insulation?Using 2-inch continuous stud panels saves 1.5 to 2.5 inches of interior depth per wall compared to traditional 2x4 wood framing, preserving roughly 3 to 5 total inches across opposing basement or interior room walls.
ComparisonsWhat is the estimated labor time in hours to frame and insulate 500 square feet of masonry wall using continuous panels versus wood stud framing?Framing and insulating 500 square feet of masonry wall takes 4 to 6 hours using interlocking continuous insulation panels, compared to 16 to 24 hours using traditional wood stud framing and batt or rigid board assemblies.
Installation ProcessWhat is the step-by-step sequence for running 12/2 Romex wiring through pre-formed electrical raceways in foam panels?To run 12/2 Romex wiring through pre-formed foam panel raceways, cut electrical box openings, snake NM-B cable through the continuous vertical and horizontal channels using fish tape, secure the boxes, and seal penetrations with low-expansion foam.
Installation ProcessWhat is the correct bead pattern and spacing for applying polyurethane adhesive to the back of continuous insulation panels?Apply a continuous 3/8-inch bead of heavy-duty polyurethane construction adhesive down the center of each embedded stud track on the back of the panel, spaced 16 inches on center, before pressing firmly against the wall.
Installation ProcessHow many inches of gap should be left between the bottom edge of continuous wall panels and the basement floor slab?Install continuous wall insulation panels with a 1/4-inch to 1/2-inch gap above the basement concrete slab to prevent capillary moisture uptake and allow proper alignment across uneven floor surfaces.
Installation ProcessWhat is the step-by-step sequence for installing corrugated container inserts and flat continuous wall panels inside a steel shipping container?To insulate a steel shipping container using InSoFast, glue corrugated EPS inserts into the wall recesses with construction adhesive, then interlock continuous flat panels over the ribs in a running bond pattern.
Installation ProcessWhat is the step-by-step process for sealing and flashing window buck openings when installing continuous exterior insulation panels?Sealing and flashing a window buck opening requires shingle-lapping self-adhered flashing from the sloped sill up to the jambs and head, integrating directly with the wall’s water-resistive barrier before mounting exterior continuous insulation panels.
Troubleshooting & RisksHow many inches out-of-plumb can a concrete wall be before requiring shimming behind interlocking foam panels?Interlocking foam panels bridge concrete wall deviations up to 1/4 inch using adhesive alone, but any out-of-plumb or bowed condition exceeding 1/4 inch over an 8-foot height requires shimming behind the embedded studs.
Troubleshooting & RisksWhat is the minimum cure time required for panel adhesive on concrete walls before hanging drywall?Panel adhesive applied to concrete walls requires a minimum cure time of 24 hours under standard conditions, though cold or high-moisture basements require 48 hours before hanging drywall to ensure full structural bond strength.
Air sealing basement rim joists and inside corner assembliesCan canned expanding spray foam be used to air seal around basement rim joist insulation cutouts?Yes, closed-cell canned expanding spray foam is an effective method to air seal around rigid insulation cutouts in basement rim joist bays, preventing drafts, thermal bridging, and interior moisture accumulation.
Selecting construction adhesives for mounting panels to steeWhich PL Premium adhesive formula is recommended for gluing foam studs to painted corrugated shipping container steel?Loctite PL Premium Polyurethane Construction Adhesive is recommended for securing foam studs and insulation panels to painted corrugated shipping container steel because moisture-cured polyurethane bonds metal without melting expanded polystyrene foam.
Running electrical wiring through InSoFast built-in panel raCan standard adjustable plastic single-gang outlet boxes mount directly into foam cutout openings?Standard adjustable plastic single-gang outlet boxes cannot anchor directly into raw foam alone; they must secure mechanically to our integrated stud, the masonry substrate, or clamp directly to the finished drywall face.
Straightening bowed or uneven masonry basement wall installaHow do you shim behind interlocking foam panels when concrete block bows inward more than 1/2 inch?To shim interlocking foam panels over concrete block bowing inward more than 1/2 inch, span the depression by placing rigid foam or composite shims behind the embedded studs and anchoring them with masonry screws or heavy adhesive.
Insulating concrete slab floors, drains, and concrete ceilinIs tongue-and-groove plywood required over floor panels before laying floating laminate flooring?Installing a minimum 1/2-inch tongue-and-groove plywood or oriented strand board subfloor over continuous insulation floor panels is required before laying floating laminate flooring to prevent joint deflection and structural failure under point loads.
Attaching drywall and interior wall finishes to embedded stuFastener spacing for securing standard 1/2-inch sheetrock to composite studsFasten standard 1/2-inch drywall to composite studs using 1-5/8-inch coarse-thread drywall screws spaced 12 inches on-center in the board field and 8 to 12 inches along all perimeter edges.
Installing continuous exterior insulation panels and exterioCan fiber cement lap siding nail directly through continuous exterior insulation into stud framing?Fiber cement lap siding can nail directly through continuous exterior insulation up to 1 inch thick into wood framing studs, but thicker foam assemblies require structural furring strips or panels with integrated fastening studs.
Shipping container interior and exterior insulation panel syShould side wall container inserts be glued in place before attaching the primary flat insulation panels?Yes, definitely. Side wall container inserts should always be glued into the steel corrugations first, creating a flush, continuous backing that eliminates condensation-causing air cavities before adhering the primary flat insulation panels over them.

Keep going

Are the panels fire resistant or do they have to be covered

Talk to us